Operating and InstallationInstructionsCeramic CombisetCS 1112CS 1122To prevent accidents andmachine damage,read these Instructionsbeforeinstallation o
One-ring burners use one heating strip,and two-ring burners and grill zonesuse two heating strips. Depending onthe model, the heating strips may besep
Turning a burner On/Off^To turn a burner on, press the controlknob down and turn it clockwise ato the desired setting.^To turn a burner off, turn the
Residual Heat IndicatorWhen a cooking zone is switched on,the On/Off indicator will light followedby the residual heat indicator.When the cooking zone
SettingsUse for Power level*Melt butter, chocolate, etc.Dissolving gelatinePrepare yogurt1-2Warming small quantities of food/liquidKeeping delicate di
Overheat protectionEach cooking zone is equipped with atemperature limiter. This featureautomatically turns off the heatingelement before the glass ce
Following these tips will allow you tomake the most of your ceramiccombiset.The cooking surfaceThe ceramic combiset is made of anextremely hard and du
Copper bottom and aluminum pansmay leave a residue on the combiset inthe form of metallic lines. This is normal.These lines can be removed using anon-
Do not use a steam cleaner to cleanthis appliance. Steam couldpenetrate electrical components andcause a short circuit. Pressurizedsteam could cause p
Stainless steelClean stainless steel surfaces withwarm water and liquid dish soapapplied with a non-abrasive spongeand then wipe dry with a soft cloth
,Repairs should only be carried out by an authorized technician inaccordance with local and national safety regulations. Unauthorized repairscould cau
IMPORTANT SAFETY INSTRUCTIONS...3Description of the combiset ...7CS 1112 ...
In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this bo
MieleCare(USA only)MieleCare, our Extended ServiceContract program; gives you theassurance of knowing that yourappliance investment is covered by 5yea
Installation InstructionsIMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USETo prevent accidentsand machine damageread these instructionsbef
Note to the installer:Please leave this instruction bookwith the consumer for the localelectrical inspector’s use.The minimum distances given inthese
Safety distances above theapplianceThe minimum safety distance given bythe hood manufacturer must bemaintained between the combiset andthe hood above
Safety distances to the sidesof the applianceThe appliance should only be installedas shown in the illustrations, whilemaintaining the required safety
Safety distance when installing the appliance near a wall with trim or a backsplashA minimum distance of 2" (50 mm) between the trim or back spla
Installation dimensions CS 1112a Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e R
Installation dimensions CS 1122a Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e R
WARNING- When using yourappliance follow basicprecautions, including thefollowing:Read all instructions beforeinstallation or use to preventinjury and
Cut out^Make the countertop cut-out for thedesired number of appliances.Remember to maintain a minimumsafety distance from the back wall,as well as fr
Installation of multipleappliancesWhen installing more than one combiset appliance, a support bar b must beinstalled between the appliances.Countertop
Sample calculations for a countertop cut-out for three appliancesAappliance widthminus 5/16"(8 mm)Bappliance widthCappliance widthminus 5/16"
a Spring clipsb Support barsc Space between support bar and countertopAn additional support bar is required for each additional appliance. The positio
Attach the spring clips andsupport barsWood or solid surface countertops^Place the supplied spring clips aand the support bars b at themarked position
^Coat the edges of the spring clips,^and the space d between the stripsand the countertop with silicone(supplied).Installation35bda
Installing the appliance^Feed the power cord down throughthe cut-out.^Then place the front side of theappliance in the countertop cut-out.^Then with a
SealingThe appliance must not be permanentlysealed into the countertop wheninstalled. The sealing strip under theedge of the appliance provides asuffi
,CAUTION: Before installation orservicing, disconnect the powersupply by either removing the fuse,shutting off the main power ormanually "trippin
Disposal of packing materialsThe cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle.Ensure that any plastic wrappings,
Technical safety~Installation, repair and maintenancework should be performed by a Mieleauthorized service technician. Work byunqualified persons coul
Alteration rights reserved / 0409For the most updated manual see the Miele web site.M.-Nr. 07 346 400 / 01M.-Nr. 07 346 400 / 01
~Defective components should bereplaced by Miele original spare partsonly. Only with these parts can themanufacturer guarantee the safety ofthe applia
~Be careful not to drop anything onthe ceramic surface of the combiset.Even lightweight objects may causedamage.~Use the proper pan size. Selectcookwa
CS 1112a Variable burner :C 4" or 7" (100 mm or 180 mm) -Power: 700 W or 1800 Wb Standard burner :C 511/16" (145 mm) -Power: 1200 Wc Bu
CS 1122a Extended burnerC 7" or 7" x 107/16"(180 mm or 180 mm x 265 mm) -Power: 1500 W / 2400 Wb Standard burnerC 511/16" (145 mm)
Clean the combiset^Before using for the first time, cleanthe appliance with a damp cloth anddry with a soft cloth.Do not use liquid dish soap to clean
Commentaires sur ces manuels