Miele F 1801 SF Manuel d'installation

Operating and InstallationInstructionsFridge-Freezer CombinationKF 1801 SFKF 1811 SFKF 1901 SFKF 1911 SFTo prevent accidentsand appliance damageread t

Niche dimensionsABKF 1801 SF, KF 1811 SF 30 ½" (774.6 mm) 30" (762 mm)KF 1901 SF, KF 1911 SF 36 ½" (927 mm) 36" (915 mm)Dimensions

Power supply and water connection1. Power supply2. Water connectionAKF 18X1 SF 15" (381 mm)KF 19X1 SF 18" (458 mm)Dimensions58

Before you beginRead these instructions completelyand carefully.Have the appliance installed by aqualified technician, according tothe enclosed instal

Aligning the housing unitThe housing unit must be carefullyaligned using a spirit level beforeinstalling the appliance. The unitcorners must be at rig

There are transportation safetydevices inside the appliance toprotect the shelves and storagecompartments until installation iscomplete. Do not remove

^Remove the cover b.^Push the module into the slot until itlocks into place.^Connect the appliance to the powersupply and turn it on. After severalsec

Mounting AccessoriesThe mounting accessories needed forinstalling the appliance into the nicheare included in the packaging. Severalplastic bags are i

^Drill pilot holes:–1/8"(3mm)for5x60mmwoodscrews–1/16"(2mm)for4x15mmwoodscrews.^ Tightly secure the anti-tip brackets inthe niche.Be certain

Securing an alternative anti-tipdeviceIf the anti-tip brackets cannot beattached securely, an alternativeanti-tip device can be used.Ensure that there

Sliding the appliance into theinstallation nicheIf a side-by-side installation isdesired, connect the two appliancestogether. See the Installation Man

Installation instructionsInformation is subject to change. Please refer to our website to obtain the mostcurrent product specification, technical &

^To prevent the power cord frombecoming caught:Tie a piece of string to the middle ofthe power cord and feed it forwardunder the appliance. When slidi

Aligning the appliance^Align the appliance with the customfront.The height-adjustable feet at the frontand rear can all be adjusted from thefront:– Fr

Attaching the appliance to theinstallation niche^Open the appliance doors.^ Fasten the appliance on the left andright hand sides with the 3 (supplied)

Attaching the toe-kick coverThe maximum height of the toe-kickcover is 4" (101 mm) from the top ofthe floor. Do not cover the ventilationslits in

Mounting the air separatorThe air separator keeps the supply andexhaust air separate. This preventswarm exhaust air from flowing into themachine, opti

All plumbing work should be carriedout by a suitably qualified andcompetent person, in accordancewith all applicable local and nationalregulations.The

Preparing the water connectionThe connection to the householdwater supply must be installedbefore the appliance is installed.^Turn off the main water

Connecting the water supplyWhen connecting the water pipe tothe solenoid valve of the appliance,follow the instructions supplied bythe manufacturer of

,Avoid the risk of electricalshock- Plug into a grounded 3-prongoutlet.- Do not move the ground plug.- Do not use an adapter.- Do not use an extension

Alteration rights reserved / 5011INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOSTCURRENT PRODUCT SPECIFICATIONS, TECHN

Disposal of packing materialsThe cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle.Ensure that any plastic wrappings,

Have the appliance installed by aqualified technician, according tothe enclosed installation instructions.,WARNINGThis appliance is top-heavy andmust

BaseA fully loaded appliance is very heavy.The load-bearing capacity of your floormust meet the following requirements:KF 18X1 SF ...1,007 lbs (45

Stainless steel panelsStainless steel door panels and toe-kickcovers are available from Miele.Installation optionsThere are many different installatio

Installation with partition using the"Merging Kit"The minimum thickness of the partitionis5/8" (16 mm).If there is a partition with a t

Adjusting the door openingangle (optional accessory)Depending on the installation site, itmay be necessary to adjust the dooropening angle to 90°.^Ope

Door dimensions (opening angle 90°)AKF 18X1 SF 325/8" (829 mm)KF 19X1 SF 3811/16" (982 mm)Door dimensions (opening angle 115°)ABKF 18X1 SF 3