Miele KM 2010 G Manuel d'installation

Operating and installation instructionsGas hobsKM 2010 / 2011 / 2012 / 2013KM 2030 / 2032 / 2033KM 2050 / 2051To avoid the risk of accidentsor damage

BurnersWok burner Small, medium and large burnersa Burner ringb Burner capc Burner headd Burner basee Ignition safety devicef IgnitorGuide to the appl

This appliance complies with allrelevant local and national safetyrequirements. Improper use of theappliance can, however, present arisk of both perso

Safety with children~This appliance is only intended foruse by adults who have read theseinstructions. This appliance is not a toy!To avoid the risk o

Technical safety~Before installation, check theappliance for visible signs of damage.Do not install and use a damagedappliance. It could be dangerous.

~During installation, maintenance andrepair work, the appliance must bedisconnected from the gas supply andmains electricity supply.~While the applian

Correct use~The appliance gets hot when in useand remains hot for quite a while after ithas been switched off. Do not touch itwhilst it could still be

~Do not heat up unopened tins offood on the hob as pressure will buildup in the tin, causing it to explode. Thiscould result in injury and scalding or

~Spray canisters, aerosols and otherinflammable substances must not bestored in a drawer under the hob.Cutlery inserts must be heat-resistant.~Always

Disposal of the packingmaterialThe transport and protective packinghas been selected from materials whichare environmentally friendly fordisposal, and

Please stick the extra data plate for the appliance suppliedwith this documentation in the space provided in the "Aftersales service" sectio

G This appliance can be used in countries other than those specified on theappliance. It is, however, set up for connection to the gas and electricity

The control is used to ignite the burner and to regulate thestrength of the flame.ßThe gas supply is turned off& Strong flame/ Weak flameThe burne

In the event of a power cutIf there is an interruption to the electricity supply the gas canbe ignited with a match.^Press in the relevant control and

Burner Min. pan base diameter in cmSmall burner 10Medium burner 12Large burner 14Wok burner 14Max. diameter at top of pan in cmSmall burner 22Medium b

–Remember when purchasing new pans that manufacturersusually refer to the diameter at the top of the pan in theirdocumentation.–Use a pan lid whenever

This appliance is fitted with a thermoelectric ignition safetydevice which cuts off the supply of gas to a burner if theflame goes out, for example if

For Miele branded and cleaning and conditioning productssee “Optional accessories”.,Do not use a steam cleaning appliance to clean thisappliance. The

Cleaning IntructionsStainless steelsurfacesClean stainless steel surfaces using an E-Cloth(see "Optional accessories") or with a solution of

To assemble the small, medium and large burners^ Place the burner head c onto the burner base d so thatthe ignition safety device e, the ignitor f and

To assemble the wok burner^ Place burner head c onto burner base d so that the theignition safety device e and the ignitor f extend throughtheir respe

,Repairs to the gas and electrical components of thisappliance must only be carried out by a suitably qualifiedand competent person to ensure safety (

Gas-heated appliancesSafety precautions to take if you smell gasß Turn off the gas emergency control valve immediately.This is usually located near th

... the ignitor on the burner does not spark.–check whether the mains fuse has tripped. If it has, contacta qualified electrician or the Miele Service

Miele offer a comprehensive range of useful accessories aswell as cleaning and conditioning products for yourappliance.These products can be ordered o

Fit the wall units and extractor hoodbefore fitting the hob to avoiddamaging the surface.~The room in which the gas hob isinstalled must be at least 2

Safety distance above the hobA minimum safety distance must bemaintained between the hob and thecooker hood above it. See the cookerhood manufacturer&

Ideally the hob should be installed withplenty of space on either side. Theremay be a wall at the rear and a tall unitor wall at one side. On the othe

KM 2010 / KM 2011 / KM 2012 / KM 2013a Frontb Casing depthc Gas connection R 1/2" ISO 7-1 (DIN EN 10226)d Mains connection box with mains connect

KM 2030a Frontb Casing depthc Gas connection R 1/2" ISO 7-1 (DIN EN 10226)d Mains connection box with mains connection cable, L = 2000 mmApplianc

KM 2032 / KM 2033a Frontb Casing depthc Gas connection R 1/2" ISO 7-1 (DIN EN 10226)d Mains connection box with mains connection cable, L = 2000

KM 2050 / KM 2051a Frontb Casing depthc Gas connection R 1/2" ISO 7-1 (DIN EN 10226)d Mains connection box with mains connection cable, L = 2000

Preparing the worktop^Make the worktop cut-out followingthe dimensions applicable.Remember to maintain a minimumsafety distance from the back wall,as

Guide to the appliance ...5Models ...5Burners ...

General installation tipDo not use any sealant unlessexpressly instructed to do so. Thesealing strip under the edge of the toppart of the appliance pr

All electrical work should be carriedout by a suitably qualified andcompetent person, in strictaccordance with current local andnational safety regula

ImportantThe electrical safety of this appliancecan only be guaranteed whencontinuity is complete between it andan effective earthing system, whichcom

,Connection to the gas supply, orconversion from one type of gas toanother, should only be undertakenby an approved and registered gasinstaller in str

ConnectionThe gas connection must be installedso that connection can be made eitherfrom inside or outside the kitchen unit,and the isolating valve mus

Nominal ratings for all gas types with the burner full onBurner Gas type KM 2010 / KM 2011 KM 2012 / KM 2013 /KM 2030kW g/h kW g/hSmallburnerNatural g

Nominal rating at low settingBurner Gas type KM 2010 / KM 2011 KM 2012 / KM 2013 / KM 2030kW kWSmallburnerNatural gasLiquid gas0.250.250.250.25Mediumb

,Connection to the gas supply, or conversion from one type of gas toanother, should only be undertaken by an approved and registered gasinstaller in s

Changing the jetsDisconnect the gas hob from theelectricity supply by switching off atthe socket or by disconnecting themains fuse.To change the main

To change the small jets(for all burners)The top of the appliance has to beremoved before the small jets can bechanged.^Loosen the fixing screws on th

ModelsKM 2010 / KM 2011a Large burnerb Small burnercd Medium burnersControls:e Front rightf Rear rightg Rear lefth Front leftGuide to the appliance5

After changing the jets^Reassemble the burner parts in thereverse order,^Check all gas fittings for leaks byoperating the burner without the topsectio

In the event of any faults which you cannot remedy yourself, or if the appliance isunder guarantee, please contact:–Your Miele dealer, or–the Miele Se

Alteration rights reserved / 2111M.-Nr. 07 181 150 / 06

KM 2012 / KM 2013a Wok burnerb Small burnercd Medium burnersControls:e Front rightf Rear rightg Rear lefth Front leftGuide to the appliance6

KM 2030a Wok burnerb Small burnercd Medium burnersControls:e Front rightf Rear rightg Rear lefth Front leftGuide to the appliance7

KM 2032 / KM 2033a Large burnerb Small burnercd Medium burnerse Wok burnerControls:f Front rightg Rear righth Middlei Rear leftj Front leftGuide to th

KM 2050 / KM 2051a Wok burnerb Small burnerc Large burnerde Medium burnersControls:f Front rightg Rear righth Middlei Rear leftj Front leftGuide to th